Photographs of DIY Audio Projects that do not fall into any of the previous categories such as DIY turntables, power supplies, pictures of your listening room setup ....
19 files, last one added on Jun 16, 2013 Album viewed 15 times
A photo gallery of the various inexpensive Tube Amplifier Kits from S-5 Electronics that have been built by DIYers. The kits include the K-8LS, K-12, K-16 and the similar K-502.
51 files, last one added on Sep 03, 2013 Album viewed 11 times
Photos of Commercial Hi-Fi Audio Gear, Components and Products.
33 files, last one added on May 15, 2012 Album viewed 5 times
8 albums on 1 page(s)
614 files in 8 albums and 1 categories with 5 comments viewed 3,490,773 times
Random files
Goldwood-Open-Baffle-Speakers-Back.jpgGoldwood Open Baffle Speakers - Rear View12569 viewsRear view of 8" and 15" Goldwood drivers on an open baffle.
BattMMPreSmall-2.jpgMM Phono Preamp (battery powered)4235 viewsMy second build of the Jaycar MM phono preamp kit is house in a sleek enclosure and runs from Three 9V lithium batteries. An Alps Blue Velvet potentiometer is topped off with a solid brass black chrome knob. The preamp is very smooth sounding and better than my earlier version which uses an AC supply and regulators on board. See the MM Phono Preamp (battery powered) - inside image for an internal sview.
BoydOutSideSmall.jpgJAN6418 sub-mini tube preamp kit MKII2868 viewsThe MKII finished Oatley kit complete with 4oz brass knob. See other image for an internal photograph. The preamp has an excellent sound with good bass extension. This build was requested by an Australian women who saw the preamp article on the diyAudioProjects.com site. For more information about these little battery powered tube amplifier kits, see the JAN6418 tube preamp / headphone amp kit.
Nelson-Pass-B1-Buffer-Preamp-rear.jpgNelson Pass B1 Buffer Preamp - rear4152 viewsDIY Nelson Pass B1 Buffer from the rear shows two selectable inputs and a single output. Compared to the Nelson Pass BoZ the mid range and treble I feel are more transparent but bass weight is less. The sound is completely un-coloured. This inexpensive simple preamp has a frequency extension from 5Hz to 780kHz and is very PS tolerant.
Mark Houston
For more information about this build see the Russian Pass B1 FET Preamp/Buffer thread on the forum.
Last additions
DIY-6AS7-Tube-Headphone-Amplifier.jpgDIY 6AS7 Tube Headphone Amplifier5781 viewsMy name is Laurie. I have been building and DIYing for 45 years now and happily will never stop. This tube headphone amp is from a thread in the Form.
The power connecting cable comes from a European Travel Iron I bought for $1.00 at junk shop. (220v/6A) They will be shortened when I find a perch for the amp and me. The sound is better than my ears have ever heard so I will be keeping this one for my retirement entertainment should such a time ever come. Wink It has worked from day one and continues to please me every time it is turned on. The tubes are JJ ECC88 / 6AS7 with a 5V4 rectifier tube. To spite it's small size the parts are quite easily accessed. I over built most components so it will outlast me I fear. The only change I anticipate may be the 6AS7 to a bottle neck glass to match the rectifier tube. I do have and use a 6080 tube, but i can tell no difference in sound. It will take more then a few hours of listening to get my ears better tuned.Feb 28, 2017
4-channel-400W-amplifier.jpg 4 channel, 400 W amplifier4457 viewsThis 4-channel 400 W amplifier uses Hypex UcD400HG modules together with the corresponding power supply.
The whole is mounted inside a Galaxy 330 x 230 x 80 case.
For building instructions, have a look at this project's wiki.
Two such amplifiers has been working for over 2 years in my lounge, driving Linn Komponent 110 loudspeakers which each have 4 speaker inputs.
Francois Corthay - Switzerland
Project Page: 4 channel 400 W amplifier using Hypex UcD400HG modules Dec 20, 2015
E88CC-SV83-SET-Amplifiers.jpgDual SV83 SET Amplifiers4588 viewsA mirrored pair of SET amplifiers, presently being used in bridged mode. All P2P construction using silver solder. I included a "Hazen grid" capacitor and input tube bias change switch. The single mA meter displays individual output tube bias current with a Left/Right switch. Edcor XPRW178 power transformer and GXSE10-6-8K output transformers. Upgraded caps to Jantzen Audio 1200V Z-Superior. Upgraded resistors to PRP PR9372 Audio for metal film and TAKMAN REX for carbon film. ALPS Blue 100K attenuator. The power supply uses a RCA 5U4GB rectifier and Hammond 156R choke. Matched pairs of Svetlana SV83 for power and JJ E88CC for the input tube.
Billy Whiten - Georgia, USADec 20, 2015
6V6-Push-Pull-Amplifier.jpgPush-Pull (PP) 6V6GT Tube Amplifier3736 viewsThis 6V6 amp was built following the DIY Push-Pull (PP) 6V6 / 6V6GT Tube Amplifier Schematic. Power Supply transformer and Output transformers are handmade in Argentina by NavasBaccino. I'd like to thank Brad S. for the help. The sound is amazing and clear, free of distortion.
